Hey there! As a supplier of the EX800 Ice Cream Extruder Machine, I often get asked about the storage requirements for this nifty piece of equipment when it's not in use. Well, let's dive right into it and figure out how to keep your EX800 in tip - top shape during those off - times.
First things first, let's talk a bit about the EX800 Ice Cream Extruder. It's a powerful and efficient machine that can really up your ice - cream production game. But like any other piece of machinery, it needs proper care and storage to ensure it lasts for a long time.
Cleaning Before Storage
Before you even think about storing the EX800, you've got to give it a thorough cleaning. This is super important because any leftover ice cream, flavorings, or other residues can cause mold and corrosion over time. Start by disassembling all the removable parts, like the extrusion nozzles, hoppers, and paddles. These parts are usually easy to take off and put back on, so don't worry about it being too complicated.
Soak the removable parts in warm, soapy water. Use a mild detergent that won't damage the machine's materials. After soaking for about 15 - 20 minutes, use a soft brush to scrub away any stubborn dirt or ice - cream bits. Rinse the parts thoroughly with clean water and let them air dry completely.
For the main body of the EX800 Ice Cream Extruder Machine, wipe it down with a damp cloth. Make sure to get into all the nooks and crannies, especially around the motor and control panel. Avoid getting water directly into the electrical components, as this can cause short - circuits and other serious problems.
Storage Location
Now that your machine is all clean, it's time to find a good place to store it. The ideal storage location should be dry, cool, and well - ventilated. A humidity level of around 40 - 60% is perfect. High humidity can lead to rust and electrical issues, while low humidity can cause some plastic parts to become brittle.
Avoid storing the EX800 in a basement or an attic if possible. Basements tend to be damp, and attics can get extremely hot during the summer. A climate - controlled storage room or a corner of your production facility that's away from direct sunlight and moisture is a great choice.
If you're storing the machine in a warehouse, make sure it's not near any chemicals or solvents. These substances can emit fumes that might damage the machine's finish and internal components. Also, keep it away from heavy machinery that could cause vibrations, as these vibrations can loosen screws and other parts over time.
Protection from Dust and Debris
Dust and debris are the enemies of any machine, and the EX800 is no exception. To protect it from these pesky particles, cover the machine with a custom - fit dust cover. You can buy these covers online or have one made specifically for the EX800. If you don't have a dust cover, you can use a large, clean sheet or tarp. Just make sure it's tightly secured so that dust can't get in.
Another thing you can do is to place the machine on a raised platform or pallet. This will keep it off the ground and prevent dust and dirt from accumulating on the bottom of the machine.
Storage of Removable Parts
The removable parts that you took off for cleaning should be stored separately. You can use plastic containers or ziplock bags to keep them organized. Label each container or bag so that you know exactly what's inside. This will make it easier when you're ready to use the machine again.
If you have any spare parts, like extra extrusion nozzles or gaskets, store them in the same way. Keeping them in a safe and organized place will ensure that they're in good condition when you need them.
Checking on the Machine Periodically
Even though the EX800 is in storage, it's a good idea to check on it every few months. This way, you can catch any potential problems early. Look for signs of rust, mold, or any loose parts. If you notice any issues, address them right away.
For example, if you see a little bit of rust starting to form, you can use a rust remover and a wire brush to clean it off. Then, apply a thin layer of lubricant to prevent further rusting.
Storage of the EX800 Ice Cream Extrusion Tunnel
If your EX800 comes with an extrusion tunnel, it also has its own storage requirements. Similar to the main machine, clean it thoroughly before storage. The tunnel usually has a cooling system, so make sure to drain any remaining coolant according to the manufacturer's instructions.
Store the extrusion tunnel in a vertical position if possible. This will prevent any damage to the internal cooling coils and other components. Just like the main machine, cover it with a dust cover and keep it in a dry, cool place.
Recommissioning the Machine
When you're ready to start using the EX800 again after storage, there are a few steps you need to take. First, inspect all the parts to make sure they're in good condition. Reassemble the removable parts carefully, making sure that everything is properly aligned and tightened.
Before you start making ice cream, run the machine for a few minutes without any ingredients. This will help to lubricate the moving parts and check if the machine is working properly. If you notice any strange noises or vibrations, stop the machine immediately and check for any loose parts or other issues.
Well, there you have it! These are the main storage requirements for the EX800 Ice Cream Extruder Machine. By following these steps, you can ensure that your machine stays in great shape and continues to produce delicious ice cream for years to come.
If you're in the market for an EX800 or have any questions about its storage or operation, don't hesitate to reach out. We're here to help you make the most of your ice - cream production. Whether you're a small - scale ice - cream shop or a large - scale manufacturer, the EX800 can be a great addition to your business.
References
- Ice Cream Machinery Handbook
- Manufacturer's Manual for EX800 Ice Cream Extruder Machine